Home > Rentals Home > Loaders > Hitachi

Hitachi ZW220-7

New Hitachi Wheel Loader for Sale

Request A Quote
View Brochure

Main Technical Specifications
MAKE Hitachi
MODEL ZW220-7

All machines are not available at all locations.

New Hitachi ZW220-7 Wheel Loader for Sale

MORE PRODUCTIVITY. LOWER OWNERSHIP COST.

Inspired by your demands for exceptional productivity at the lowest possible cost of ownership, the ZX220-7 offers industry-leading efficiency, comfort and safety.

Dimensions
Length 27’11”/28’2” (Weld-on teeth General Purpose Standard Arm)
27’6”/27’9” (Bolt-on cutting edge General Purpose Standard Arm)
28’8” (Weld-on teeth/segment edge Rock Bucket Standard Arm)
29’2”/29’4” (Bolt-on cutting edge General Purpose High-lift Arm)
WO/Bucket
23’4” (Weld-on teeth & Bolt-on cutting edge General Purpose & Weld-on teeth/segment edge Rock Bucket Standard Arm)
24’12” (Bolt-on cutting edge General Purpose High-lift Arm)
Width 9’3”
Height 11’1”
Wheelbase 10’10”
Ground Clearance 1’6”
Turning Radius 19’9” (centerline of outside tire)
11’7” (inside of tires)
Operating Weight 40,109-41,035 lbs.
Steering Angle Each direction 37°; total 74°
Final Drive Heavy-duty planetary, mounted inboard
Tread 7’1”
Loader Clearance Radius 22’11”-22’12” (Weld-on teeth General Purpose Standard Arm)
22’9”-22’10” (Bolt-on cutting edge General Purpose Standard Arm)
23’2” (Weld-on teeth/segment edge Rock Bucket Standard Arm)
23’5”-23’6” (Bolt-on cutting edge General Purpose High-lift Arm)
Engine
Engine Make Cummins
Engine Model B6.7
Engine Type Direct injection
Cylinders 6
Gross Horsepower 210 HP
Net Horsepower 204 HP
Cooling Water-cooled
Bore x Stroke 4.2” x 4.9”
Displacement 410.1 cu.in
Air Cleaner Two element dry type with restriction indicator
Fuel Tank Capacity 67.3 Gallons
Battery 2 x 12 V
Aspiration Turbocharger and intercooled
Cycles 4
Emission Standards EPA Final Tier 4/EU Stage V
Torque Converter Three element, single stage, single phase
After-Treatment DPF+SCR system
Final Reduction Gear Two stage reduction with limited slip differential
Cooling Method Forced circulation type
Drivetrain
Axles Semi-floating (front and rear)
Front: fixed to the front frame
Rear: Trunnion support
Transmission Type Torque convertershaft type powershift with computer-controlled automatic shift and manual shift features included
Torque 990 Nm at 1300 min
Drive System Four-wheel drive system
Brakes Service: inboard mounted fully hydraulic 4 wheel wet disc brake. Front and rear independent brake circuit.
Parking: Spring applied, hydraulically released, dry disc type with external output shaft
Tires 23.5R25 (L3)
Hydraulic
Pump Main: Variable displacement axial plunger pump
Fan: Fixed displacement gear pump
Hydraulic Tank Capacity 30.1 Gallons
Hydraulic Flow Main Pump: 72.6 Gallons
Fan Pump: 17.4 Gallons
Hydraulic Cylinders Double acting type
No. x Bore x Stroke: Arm-2 x 5.1” x 34.6” & Bucket-1 x 6.5” x 20.1”
Hydraulic Cycle Time Lift arm raise: 5.6 seconds
Lift arm lower: 3.3 seconds
Bucket Dump: 1.5 seconds
Total: 10.4 seconds
Hydraulic Pressure Main Pump: 3,974 PSI
Fan Pump: 2,756 PSI
Hydraulic Filter Full-flow 9 micron return filter in reservoir
Operational
Bucket Width 9’7”
Dig Depth 4” (Weld-on teeth & Bolt-on cutting edge General Purpose Standard Arm)
6” (Weld-on teeth/segment edge Rock Bucket Standard Arm)
7” (Bolt-on cutting edge General Purpose High-lift Arm)
Bucket Capacity 3.6 yd³-7.8 yd³
Height to Bucket Pin 1’5” (carry height at carry position)
13’5” (Weld-on teeth & Bolt-on cutting edge General Purpose & Weld-on teeth/segment edge Rock Bucket Standard Arm)
14’9” (Bolt-on cutting edge General Purpose High-lift Arm)
Dump Reach 4’ & 4’2” (Weld-on teeth General Purpose Standard Arm)
3’8” & 3’10” (Bolt-on cutting edge General Purpose Standard Arm)
4’5” (Weld-on teeth/segment edge Rock Bucket Standard Arm)
4’2” & 4’4” (Bolt-on cutting edge General Purpose High-lift Arm)
Bucket Breakout Force 32,634/35,060 lbs. (Weld-on teeth General Purpose Standard Arm)
30,429/32,414 lbs. (Bolt-on cutting edge General Purpose Standard Arm)
29,547 lbs. (Weld-on teeth/segment edge Rock Bucket Standard Arm)
27,783/29,548 lbs. (Bolt-on cutting edge General Purpose High-lift Arm)
Steering Articulated frame steering
Travel Speed - Forward 1st: 3.9 MPH
2nd: 6.8 MPH
3rd: 9.9 MPH
4th: 14.7 MPH
5th: 22.5 MPH
Travel Speed - Reverse 1st: 4.1 MPH
2nd: 7.1 MPH
3rd: 15.4 MPH
4th: 14.7 MPH
5th: 22.5 MPH
Breakout Force 32,634 lbf
Oscillation Angle Total 24° (+12°, -12°)
Rollback Angle 47° at carry position w/standard arm
46° at carry position w/high-lift arm
43° at carry position w/standard arm
44° at carry position w/high-lift arm
60° at carry position w/standard arm
52° at carry position w/high-lift arm
Dump Clearance 9’2” & 8’12” (Weld-on teeth General Purpose Standard Arm)
9’6” & 9’4” (Bolt-on cutting edge General Purpose Standard Arm)
8’8” (Weld-on teeth/segment edge Rock Bucket Standard Arm)
10’10” & 10’8” (Bolt-on cutting edge General Purpose High-lift Arm)
Static Tipping Load 33,582 & 33,494 lbs. (straight) & 29,745 & 33,494 lbs. (full 37 degree turn) (Weld-on teeth
33,009 & 32,921 lb. (straight) & 33,009 & 29,062 lbs. (full 37 degree turn) (Bolt-on cutting edge General Purpose Standard Arm)
32,678 lbs. (straight) & 13,070 lbs. (full 37 degree turn) (Weld-on teeth/segment edge Rock Bucket Standard Arm)
25,975/26,151 lbs. (straight) & 22,800/22,976 lbs. (full 37 degree turn) (Bolt-on cutting edge General Purpose High-lift Arm)
Operating Height 18’1”-18’3” (Weld-on teeth & Bolt-on cutting edge General Purpose Standard Arm)
17’9” (Weld-on teeth/segment edge Rock Bucket Standard Arm)
19’5” & 19’7” (Bolt-on cutting edge General Purpose High-lift Arm)
Main Clutch Wet hydraulic, multi-disc type
Steering Cylinders Double-acting piston type
Steering Bore x Stroke Number: 2
2.8” x 17.4”
Arm Controls Arm and bucket controlled by multifunction lever
Four position valve; Raise, hold, lower, float
Bucket Controls Bucket controls w/automatic bucket return-to-dig control
Three position valve; Roll back, hold, dump
Lift Arm Clearance 12’4” (Weld-on teeth & Bolt-on cutting edge General Purpose & Weld-on teeth/segment edge Rock Bucket Standard Arm)
13’9” (Bolt-on cutting edge General Purpose High-lift Arm)

  • ENGINE
    • Aftertreatment device
    • Aftertreatment manual regeneration inhibit switch
    • Aftertreatment manual regeneration switch
    • Air filter double elements
    • Air intake: Pre-cleaner (sy-klone)
    • Air filter double elements
    • Anti-clogging radiator (wide fin pitch)
    • Automatic reversible cooling fan with heat sensing
    • Cartridge-type engine oil filter
    • Cartridge-type fuel main filter
    • Cartridge-type fuel pre-filter
    • Coolant reservoir sight gauge
    • DEF/AdBlue® tank extension filler
    • DEF/AdBlue® tank with ISO magnet adapter
    • Engine auto shut-down control system
    • Engine oil remote drain
    • Fan guard
  • BRAKE SYSTEM
    • Front and rear independent brake circuit
    • Inboard mounted fully hydraulic 4 wheel wet disc
    • Spring-applied/Hydraulic-released parking brake
  • HYDRAULIC SYSTEM
    • Bucket auto leveler (automatic return to dig control)
    • Electric control lever
      • for 3 spools control valve
        • MF lever and Proportional switch for 3rd function
    • Control lever lock switch
    • Dual lift arm auto leveler and kickout system
    • Hydraulic filters
    • Lift arm float system
    • Quick coupler piping and switch
    • Reservoir sight gauge
    • Ride control system (OFF-AUTO type)
    • Work mode selector
  • CAB
    • Adjustable steering column with POP-UP
    • Auto control air conditioner
      • with double intake filter
    • Bluetooth® integrated DAB+radio, hands-free calling
    • Camera and monitor
      • Rear view camera and monitor
    • Coat hook
    • Evacuation hammer
    • Front/rear defroster
    • Glove compartment
    • LED room light
    • Payload checker with tip-off function
    • Rear view mirrors
      • Inside (1)
      • Standard outside mirrors
      • Premium Outside (heated, 2) electrical adjustment retractable mirror stay
    • Retractable seat belt,2.0 in (50 mm)
    • ROPS (ISO 3471: 2008), FOPS (ISO 3449: 2008 LEVEL ll):
    • multi-plane isolation mounted for noise,vibration reduction
    • Rubber floor mat
    • Seat: Heavy duty air suspension seat equipped with horizontal suspension headrest and heater: fabric, high back, adjustable for damper, inclination of the seat, seat depth, weight-height, fore-aft position, reclining angle, armrest angle, headrest height and angle, lumbar support
    • Seat belt reminder
    • Steering system: Wheel steering
    • Storage
      • Cup holder
      • Document holder
      • Hot and cool box
      • Seatback pocket
      • Smartphone and Tablet device holder
    • Sunscreen roller type
    • Textured steering wheel with spinner knob
    • Tinted safety glass
      • Front windshield: laminated
      • Others: tempered
    • USB power supply
    • Windshield washer front and rear
    • Windshield wipers front and rear
    • 2 speakers
    • 8 inch sub monitor
  • MONITORING SYSTEM
    • Gauge: coolant temperature, fuel level, transmission oil temperature
    • Indicator lights: clearance lights, control lever lock, fuel level, high beam, parking brake, preheat, turn signals, work lights, fan reverse indicator, seat belt indicator
    • Indicator on multifunction monitor: F-N-R shift position, gear shift position, clock, DEF alarm indicator, DEF level gauge, ECO indicator, forward/reverse selector switch indicator, hold display, hour meter, joystick steering indicator (optional), odometer, battery volt, speedometer, tachometer, transmission auto-shifting indicator, Warning lights: air filter restriction, brake oil low pressure, communication system error, discharge warning, engine oil low pressure, engine warning, hydraulic oil level, low steering oil pressure, overheat, transmission warning
    • Indicator on sub monitor: payload checker, dual auto-leveler indicator rear obstacle detection and warning system (optional)
    • 38 languages selection
  • ELECTRICAL SYSTEM
    • Alternator (95 A)
    • Backup alarm
    • Battery disconnect switch
    • Large capacity batteries
    • Power outlet 12 V and 24 V
  • LIGHTS
    • Clearance lights
    • LED brake and tail lights
    • LED headlights
    • Turn signals with hazard switch
    • Work lights: 4 front, 2 rear on cab and 2 rear LED working lights (high brightness)
  • POWER TRAIN
    • Approach speed control
    • Automatic transmission with load sensing system
    • Clutch cut position switch
    • Differential: LSD (limited slip differential, front and rear)
    • DSS (down shift switch)
    • Forward/reverse lever
    • Forward/reverse selector switch
    • Maximum gear limited switch
    • Power mode switch
    • Quick power switch
    • Travel mode selector (auto1-auto2)
  • TIRES
    • 23.5R25 (L3) VJT
  • MISCELLANEOUS
    • Articulation lock bar
    • Cab top rail
      • Front rail on the cab top
      • Rear rail on the cab top
    • Cab window cleaning foot plate
    • Counterweight, built-in
    • Drawbar with locking pin
    • Emergency steering
    • Fenders for 23.5R25 (front and half covered rear fenders with mud flaps)
    • Global e-Service
    • Lift and tie down hooks
    • Lift arm: Standard lift arm
    • On board information controller
    • Vandal Protection
      • Battery cover with locking bracket
      • Lockable engine cover
    • Radiator dust protection screen
    • Standard tool kit
    • Tool box

  • ENGINE
    • Air intake: Pre-cleaner (Turbo II)
  • HYDRAULIC SYSTEM
    • Electric control lever
      • for 3 spools control valve
        • 2 levers and AUX lever for 3rd function—Inside layout pattern (3rd—bucket—liftarm)
  • CAB
    • Auto control air conditioner
      • Pre-cleaner for air conditioner
    • Camera and monitor
      • AERIAL ANGLE (Side and rear view camera)
    • Rear obstacle detection system
  • LIGHTS
    • Rotating lamp
  • POWER TRAIN
    • Driving speed limiter (12.4 mph (20 km/h))
  • MISCELLANEOUS
    • Auto lubrication system
    • Belly guard (bolt on type) (front/rear)
    • Bucket cylinder guard
    • Fenders: for 23.5R25 (front and full covered rear fenders with mud flaps)
    • Lift arm: High lift arm
    • Radiator dust protection screen

Hitachi ZW220-7

print
6715 W. Reno
Oklahoma City, OK 73127 Phone: 888.861.0219
www.kirby-smith.com
CUSTOMER
DATE
PRICE
SALESPERSON

New Hitachi ZW220-7 Wheel Loader for Sale

MORE PRODUCTIVITY. LOWER OWNERSHIP COST.

Inspired by your demands for exceptional productivity at the lowest possible cost of ownership, the ZX220-7 offers industry-leading efficiency, comfort and safety.
GENERAL INFORMATION
Manufacturer
Hitachi
Model Year
Model
ZW220-7
Condition
NEW
Dimensions
Length
27’11”/28’2” (Weld-on teeth General Purpose Standard Arm) 27’6”/27’9” (Bolt-on cutting edge General Purpose Standard Arm) 28’8” (Weld-on teeth/segment edge Rock Bucket Standard Arm) 29’2”/29’4” (Bolt-on cutting edge General Purpose High-lift Arm) WO/Bucket 23’4” (Weld-on teeth & Bolt-on cutting edge General Purpose & Weld-on teeth/segment edge Rock Bucket Standard Arm) 24’12” (Bolt-on cutting edge General Purpose High-lift Arm)
Width
9’3”
Height
11’1”
Wheelbase
10’10”
Ground Clearance
1’6”
Turning Radius
19’9” (centerline of outside tire) 11’7” (inside of tires)
Operating Weight
40,109-41,035 lbs.
Steering Angle
Each direction 37°; total 74°
Final Drive
Heavy-duty planetary, mounted inboard
Tread
7’1”
Loader Clearance Radius
22’11”-22’12” (Weld-on teeth General Purpose Standard Arm) 22’9”-22’10” (Bolt-on cutting edge General Purpose Standard Arm) 23’2” (Weld-on teeth/segment edge Rock Bucket Standard Arm) 23’5”-23’6” (Bolt-on cutting edge General Purpose High-lift Arm)
Engine
Engine Make
Cummins
Engine Model
B6.7
Engine Type
Direct injection
Cylinders
6
Gross Horsepower
210 HP
Net Horsepower
204 HP
Cooling
Water-cooled
Bore x Stroke
4.2” x 4.9”
Displacement
410.1 cu.in
Air Cleaner
Two element dry type with restriction indicator
Fuel Tank Capacity
67.3 Gallons
Battery
2 x 12 V
Aspiration
Turbocharger and intercooled
Cycles
4
Emission Standards
EPA Final Tier 4/EU Stage V
Torque Converter
Three element, single stage, single phase
After-Treatment
DPF+SCR system
Final Reduction Gear
Two stage reduction with limited slip differential
Cooling Method
Forced circulation type
Drivetrain
Axles
Semi-floating (front and rear) Front: fixed to the front frame Rear: Trunnion support
Transmission Type
Torque convertershaft type powershift with computer-controlled automatic shift and manual shift features included
Torque
990 Nm at 1300 min
Drive System
Four-wheel drive system
Brakes
Service: inboard mounted fully hydraulic 4 wheel wet disc brake. Front and rear independent brake circuit. Parking: Spring applied, hydraulically released, dry disc type with external output shaft
Tires
23.5R25 (L3)
Hydraulic
Pump
Main: Variable displacement axial plunger pump Fan: Fixed displacement gear pump
Hydraulic Tank Capacity
30.1 Gallons
Hydraulic Flow
Main Pump: 72.6 Gallons Fan Pump: 17.4 Gallons
Hydraulic Cylinders
Double acting type No. x Bore x Stroke: Arm-2 x 5.1” x 34.6” & Bucket-1 x 6.5” x 20.1”
Hydraulic Cycle Time
Lift arm raise: 5.6 seconds Lift arm lower: 3.3 seconds Bucket Dump: 1.5 seconds Total: 10.4 seconds
Hydraulic Pressure
Main Pump: 3,974 PSI Fan Pump: 2,756 PSI
Hydraulic Filter
Full-flow 9 micron return filter in reservoir
Operational
Bucket Width
9’7”
Dig Depth
4” (Weld-on teeth & Bolt-on cutting edge General Purpose Standard Arm) 6” (Weld-on teeth/segment edge Rock Bucket Standard Arm) 7” (Bolt-on cutting edge General Purpose High-lift Arm)
Bucket Capacity
3.6 yd³-7.8 yd³
Height to Bucket Pin
1’5” (carry height at carry position) 13’5” (Weld-on teeth & Bolt-on cutting edge General Purpose & Weld-on teeth/segment edge Rock Bucket Standard Arm) 14’9” (Bolt-on cutting edge General Purpose High-lift Arm)
Dump Reach
4’ & 4’2” (Weld-on teeth General Purpose Standard Arm) 3’8” & 3’10” (Bolt-on cutting edge General Purpose Standard Arm) 4’5” (Weld-on teeth/segment edge Rock Bucket Standard Arm) 4’2” & 4’4” (Bolt-on cutting edge General Purpose High-lift Arm)
Bucket Breakout Force
32,634/35,060 lbs. (Weld-on teeth General Purpose Standard Arm) 30,429/32,414 lbs. (Bolt-on cutting edge General Purpose Standard Arm) 29,547 lbs. (Weld-on teeth/segment edge Rock Bucket Standard Arm) 27,783/29,548 lbs. (Bolt-on cutting edge General Purpose High-lift Arm)
Steering
Articulated frame steering
Travel Speed - Forward
1st: 3.9 MPH 2nd: 6.8 MPH 3rd: 9.9 MPH 4th: 14.7 MPH 5th: 22.5 MPH
Travel Speed - Reverse
1st: 4.1 MPH 2nd: 7.1 MPH 3rd: 15.4 MPH 4th: 14.7 MPH 5th: 22.5 MPH
Breakout Force
32,634 lbf
Oscillation Angle
Total 24° (+12°, -12°)
Rollback Angle
47° at carry position w/standard arm 46° at carry position w/high-lift arm 43° at carry position w/standard arm 44° at carry position w/high-lift arm 60° at carry position w/standard arm 52° at carry position w/high-lift arm
Dump Clearance
9’2” & 8’12” (Weld-on teeth General Purpose Standard Arm) 9’6” & 9’4” (Bolt-on cutting edge General Purpose Standard Arm) 8’8” (Weld-on teeth/segment edge Rock Bucket Standard Arm) 10’10” & 10’8” (Bolt-on cutting edge General Purpose High-lift Arm)
Static Tipping Load
33,582 & 33,494 lbs. (straight) & 29,745 & 33,494 lbs. (full 37 degree turn) (Weld-on teeth 33,009 & 32,921 lb. (straight) & 33,009 & 29,062 lbs. (full 37 degree turn) (Bolt-on cutting edge General Purpose Standard Arm) 32,678 lbs. (straight) & 13,070 lbs. (full 37 degree turn) (Weld-on teeth/segment edge Rock Bucket Standard Arm) 25,975/26,151 lbs. (straight) & 22,800/22,976 lbs. (full 37 degree turn) (Bolt-on cutting edge General Purpose High-lift Arm)
Operating Height
18’1”-18’3” (Weld-on teeth & Bolt-on cutting edge General Purpose Standard Arm) 17’9” (Weld-on teeth/segment edge Rock Bucket Standard Arm) 19’5” & 19’7” (Bolt-on cutting edge General Purpose High-lift Arm)
Main Clutch
Wet hydraulic, multi-disc type
Steering Cylinders
Double-acting piston type
Steering Bore x Stroke
Number: 2 2.8” x 17.4”
Arm Controls
Arm and bucket controlled by multifunction lever Four position valve; Raise, hold, lower, float
Bucket Controls
Bucket controls w/automatic bucket return-to-dig control Three position valve; Roll back, hold, dump
Lift Arm Clearance
12’4” (Weld-on teeth & Bolt-on cutting edge General Purpose & Weld-on teeth/segment edge Rock Bucket Standard Arm) 13’9” (Bolt-on cutting edge General Purpose High-lift Arm)

Legal Notice: Manufacturer Name, Logo and Model Information are Registered Trademarks of the Manufacturer.
Specifications and other information are subject to change without notice. No representation of accuracy is made.
Image is believed to be in the public domain or used with permission.
All machines are not available at all locations.